57 results for "Go Directreg Ethanol Vapor"

• Go Direct Ethanol Vapor Troubleshooting and FAQ ...

  Specifications and User Guide TROUBLESHOOTING -Primary Test: Place the sensor over a sample containing 1% ethanol. The readings will rise within a minute to near...

  https://www.vernier.com/til/4303

• Why does the Go Direct Ethanol Vapor read 100% after ...

  If you calibrate the and the software cannot apply a proper function, the sensor will report that it is reading 100%. Verify that you are...

  https://www.vernier.com/til/4341

• Why does the split stopper not hold the shaft of the Go ...

  The shaft of the is slightly smaller than the . This means that the stopper will not hold the Go Direct Ethanol Vapor in place....

  https://www.vernier.com/til/4340

• Can I use Vernier ethanol sensors to measure the amount of ...

  The Go Direct ® Ethanol Vapor (GDX-ETOH) and Ethanol Sensor (ETH-BTA) should not be exposed to concentrations of ethanol greater than 3%. To determine the amount of ethanol produced from a standard fermentation you will need to dilute your sample into a range that the ethanol sensor can measure.

  https://www.vernier.com/til/2906

• Can Vernier ethanol sensors be used in liquid? - Technical ...

  No. The and are gas sensors that detect ethanol vapor. The sensors needs to be placed above a liquid sample. The use of (one roll...

  https://www.vernier.com/til/2859?keyword=tape

• Do you have written instructions for experiments that use ...

  The Go Direct ® Ethanol Vapor (GDX-ETOH) or the Ethanol Sensor (ETH-BTA) can be used for these experiments. Share this post Prices shown are valid only for United States.

  https://www.vernier.com/til/2861

• Do I need to calibrate Vernier ethanol sensors ...

  For best results at high concentrations (1.0–3.0%), calibrate using 3.0% and 1% ethanol. If you are measuring an intermediate range you can also calibrate using 0.2% and 2.0% ethanol. Both the Go Direct ® Ethanol Vapor (GDX-ETOH) and the Ethanol Sensor (ETH-BTA) can be calibrated this way.

  https://www.vernier.com/til/2864

• Go Direct Mini GC Compound Library

  Sample Chromatogram Chemical and Parameters Methanol Volume (µL): 0.3Start Temp (℃): 40 Hold Time (min): 1Ramp Rate (℃/min): 10Final Temp (℃): 60Hold Time (min): 5Pressure...

  http://www.vernier.com/til/7788/

• My school is moving to iPad. Will the probeware I already own work with an iPad?

  As schools move to new technology platforms, many teachers have asked us for advice on how to make the most cost effective use of probeware...

  http://www.vernier.com/til/7711/

• How do I get OpenSciEd curriculum?

  To use Vernier technology with the OpenSciEd curriculum, you need to A) download the complete unit from OpenSciEd B) download the Vernier supplement The Vernier...

  http://www.vernier.com/til/4568/

• Why is my VSMT force sensor stuck at 1000 N?

  There are at least two possible causes for the force sensor to read a high constant value. It has been stressed beyond its capacity and...

  http://www.vernier.com/til/3463/

• How do I know if my LabQuest will work with Go Direct Sensors and Go Wireless devices?

  Only the , connected via USB can be used with the original LabQuest. All other Go Direct sensors are not supported. All models of LabQuest...

  http://www.vernier.com/til/3085/

• How does Logger Pro calculate velocity and acceleration from Motion Detector data?

  This information pertains to data collected using any of our ultrasonic motion detectors, rotary motion sensors, the Motion Encoder System, and the Go Direct Sensor...

  http://www.vernier.com/til/1011/

• How do I tell which model Go!Link I have?

  The Go!Link originally came out in 2004. As time went on some of the components we were using in the original design were no longer...

  http://www.vernier.com/til/4389/

• Problems with force sensor giving bad readings because hex barrel has been removed and improperly reinstalled.

  This article refers to the following products: All three of these sensors have a hexagonal barrel, or standoff, extending from the sensor case. This part...

  http://www.vernier.com/til/2149/

• Graphical Analysis 4 Bluetooth issues on Windows 10: Do I need to pair?

  If your Go Direct sensor works on Windows 10 via USB, but you are having issues connecting via Bluetooth wireless technology, the first thing you...

  http://www.vernier.com/til/4053/

• Graphical Analysis or Spectral Analysis launches on my Chromebook but won't connect to USB devices.

  When using a Chromebook, make you are using the Chrome version of the app. Many Chromebooks are able to run Android apps from the Google...

  http://www.vernier.com/til/4359/

• Go Wireless Temp cannot be used with Windows 10 Creators Update and Logger Pro

  On April 11, 2017, Microsoft released a major update to Windows 10. Called the Creator’s Update, the build number is 15063. This new version of...

  http://www.vernier.com/til/3960/

• How do I share data from Graphical Analysis 4?

  Graphical Analysis 4 data files can be saved from within the application as files with an .ambl extension. From there, files can be shared with...

  http://www.vernier.com/til/3771/

• How can I create FFTs using the Go Direct Sound Sensor (GDX-SND)?

  , can capture waveforms using its Microphone channel, but currently Graphical Analysis 4 will not yet create FFTs. If you have a Go Direct Sound...

  http://www.vernier.com/til/4302/

• What programming environments do you support for using your sensors for projects and teaching coding?

  Since we started this company in the early 1980’s, we have always tried to provide a way for teachers and students to “do their own...

  http://www.vernier.com/til/4307/

• Vernier Structures & Materials Tester (VSMT) Troubleshooting and FAQs

  Specifications and User Guide TROUBLESHOOTING – Primary Test: The VSMT Force sensor will auto-ID with supported releases of software. – Secondary Test: The VSMT Displacement...

  http://www.vernier.com/til/3344/

• Can I use Vernier Go Direct sensors with non-Vernier software?

  Yes, Vernier Go Direct sensors can connect to a few select applications besides Vernier Graphical Analysis 4. Additionally, you can connect to and collect data...

  http://www.vernier.com/til/4440/

• How to I set up my Raspberry Pi to use GDX sensor with Python?

  The Vernier Go Direct Python library can be installed and used on a Raspberry Pi. It can be installing by doing the following. Install the...

  http://www.vernier.com/til/4445/

• Do Vernier apps run in Windows 10 S?

  No. Windows 10 has an “S” mode that restricts what apps can be installed. Schools may opt to run Windows 10 only in S Mode,...

  http://www.vernier.com/til/4446/

• My school is moving to Chromebooks. Will the probeware I already own work with a Chromebook?

  As schools move to new technology platforms, many teachers have asked us for advice on how to make the most cost effective use of probeware...

  http://www.vernier.com/til/2871/

• Do you have data-collection technology that works with Google Chromebooks?

  Yes, Graphical Analysis 4, our data-collection and analysis application available for Chromebooks, is free and available for Download in the Chrome Web Store. Data collection...

  http://www.vernier.com/til/2453/

• My Go Direct SpectroVis Plus Spectrophotometer intermittently drops the connection while using Bluetooth.

  Note: This document addresses intermittent Bluetooth connections. If you are unable to connect at all by Bluetooth see:      [til 4118] If your successfully connects to...

  http://www.vernier.com/til/4425/

• How do I use the Moment of Inertia Kit with the original CFA?

  You can collect angular velocity data using the attached to the beam of the . However, you must use a photogate to collect angular velocity...

  http://www.vernier.com/til/4428/

• Can I use Vernier sensors with LEGO MINDSTORMS EV3?

  Yes, you can combine Vernier sensors with LEGO EV3. There are different methods to combine Vernier sensors with , depending on the software you are...

  http://www.vernier.com/til/4380/

• How do I use Google Science Journal with Go Direct sensors on Android?

  Vernier and Google introduced support for Go Direct sensors with Graphical Analysis 4 for Android in 2019. The information below is about using Google Science...

  http://www.vernier.com/til/4413/

• How do I set up Google Science Journal for data collection with Go Wireless sensors?

  The information below is about using Google Science Journal with Vernier’s now-discontinued Go Wireless sensors only. Vernier and Google introduced support for Go Direct sensors...

  http://www.vernier.com/til/3823/

• Can I do data logging using MINDSTORMS EV3 software?

  Yes. There are several different options for logging data with the EV3 using MINDSTORMS software. Here are the various data logging options: 1. Live Data...

  http://www.vernier.com/til/3569/

• Go!Link Troubleshooting and FAQs

  Product Overview [til 1908] [til 1901] [til 1469] [til 1514] [til 2107] [til 2625] [til 2871] [til 1961] [til 1721] [til 2063] Troubleshooting The LED...

  http://www.vernier.com/til/2114/

• LEGO® Mindstorms® EV3 Troubleshooting and FAQs

  LEGO® Mindstorms® EV3 units are able to work with Vernier sensors using our LEGO Sensor Adapter for EV3 and NXT (order code: BTA-NXT, $39) and...

  http://www.vernier.com/til/3339/

• How can I zero the sensor readings on my EV3?

  The Vernier Sensor Block for MINDSTORMS EV3 software does not have a Zero function. You can easily create a correction in your program to effectively...

  http://www.vernier.com/til/3608/

• Why does Port View indicate I have plugged in an NXT Sound Sensor when I have a Vernier sensor connected?

  The EV3 was designed to automatically identify EV3 and NXT LEGO sensors that have been connected to any of its input ports. Unfortunately, it does...

  http://www.vernier.com/til/3607/

• When I use the Vernier EV3 Sensor Block why is there an exclamation point above the port number?

  The exclamation is simply a notification that you have connected a non-LEGO® sensor into one of the EV3 ports. It does not interfere with the...

  http://www.vernier.com/til/3606/

• Why don't I see the Vernier Sensor block in my MINDSTORMS EV3 Sensor palette?

  You need to import the Vernier Sensor Block into MINDSTORMS. For instructions for downloading the Sensor Block, go to this web page: https://www.vernier.com/engineering/lego-ev3/ev3-sensor-block/ [til 3339]

  http://www.vernier.com/til/3605/

• How do I get the sensor reading from the Vernier EV3 Sensor block connected to the Display block?

  To display a sensor reading on the screen of the EV3, you must configure the Display block to allow sensor readings to be wired as...

  http://www.vernier.com/til/3604/

• What can I do to make my Vernier sensor readings more steady in my EV3 program?

  The Vernier sensor block for LEGO MINDSTORMS EV3 includes an option for oversampling. Oversampling takes a large number of samples and returns an averaged reading....

  http://www.vernier.com/til/3603/

• My Vernier sensor does not seem to work with my EV3 LEGO Robot. How do I troubleshoot this?

  The following are a series of troubleshooting steps that should help you find the issue: 1. Check to verify that your EV3 is on. Periodically,...

  http://www.vernier.com/til/3602/

• My LEGO EV3 program is not working. How do I start troubleshooting?

  In most cases, the LEGO EV3 program does exactly what you have programmed it to do. If you are having trouble, follow these troubleshooting steps:...

  http://www.vernier.com/til/3601/

• Why are certain sensors not able to work with the NXT Adapter?

  The answer depends on the sensor: First of all, only sensors with the BTA connector can work with this adapter. This eliminates all the BTD,...

  http://www.vernier.com/til/2585/

• Is there a way to connect my CO2 sensor to an NXT Mindstorm?

  (This information refers to the LEGO NXT robotics system. The information should be similar for LEGO EV3. However, this has not been tested.) There is...

  http://www.vernier.com/til/2236/

• Why does my LEGO solar tracker only move in one direction?

  There are two issues that may cause this to happen. 1. The reading from the is not centered around zero (0). You can determine this...

  http://www.vernier.com/til/3432/

• Scratch and Go! FAQs and Troubleshooting

  Scratch is a free, browser-based programming language that is designed for students ages 8 to 16, and it is supported by an active community of...

  http://www.vernier.com/til/3764/

• Which sensors can I use with Graphical Analysis 4 and Graphical Analysis GW on Android devices?

  We encourage you to use Graphical Analysis 4 whenever possible; however, support for some devices is not yet included in this application. Use the information...

  http://www.vernier.com/til/4190/

• Why am I getting Motion Detector readings that are noisy or max out at a certain distance?

  The following tips for Motion Detectors apply to all of the following products: The maximum sample rate that you can use for the motion detector...

  http://www.vernier.com/til/5/

• Can I use Vernier sensors with LEGO MINDSTORMS NXT?

  Yes, you can connect Vernier sensors to a LEGO NXT or EV3 (the EV3 is LEGO’s newer model robot platform, the NXT is the older...

  http://www.vernier.com/til/4376/

• What Bluetooth radio do I need for Go Direct Sensors and Python?

  To connect to your Go Direct device to Python via Bluetooth® wireless technology, you will need a Bluegiga BLED112 Bluetooth® Low Energy Dongle. https://www.silabs.com/products/wireless/bluetooth/bluetooth-low-energy-modules/bled112-bluetooth-smart-dongle Related...

  http://www.vernier.com/til/4370/

• Should I buy EasyTemp or Go!Temp to work with both Texas Instruments calculators and computers/Chromebooks?

  Because of the lower overall cost, we recommend you purchase the following:           The Go!Temp cable has a standard USB connector for connecting to a computer...

  http://www.vernier.com/til/4364/

• Should I buy EasyLink or Go!Link to work with both Texas Instruments calculators and computers/Chromebooks?

  Because of the lower overall cost, we recommend you purchase the following:             The Go!Link has a 1 m cable with a standard USB...

  http://www.vernier.com/til/4363/

• Which motion detector should I buy? What are the differences between them?

  We sell multiple motion detectors. The motion detectors we sell are very similar and use the same ultrasonic technology. The choice of which to buy...

  http://www.vernier.com/til/2996/

• What motion detector should I buy that will work with both calculators and computers/Chromebooks?

  If you need a motion detector that works with both Texas Instruments calculators as well as computers or Chromebooks, you should purchase the following: The...

  http://www.vernier.com/til/4362/

• What equipment do I need for the LEGO-EV3 Engineering Projects book?

  , contains 13 engineering challenges. Here is an outline of the Vernier and LEGO equipment required for the projects: Vernier Equipment To perform all of...

  http://www.vernier.com/til/3905/

• What is the purpose of the spring clip on the shaft of the Go Direct Centripetal Force Apparatus?

  The clip is designed to hold the in place when using the . The sensor rests on this clip and rotates with the shaft to...

  http://www.vernier.com/til/4345/