Search
Hand Air Pump- Vernier Projectile Launcher Troubleshooting and FAQs – Technical ...
- Dec 16, 2018 ... Replacement Parts. Wax Tape (300 feet) (WXT-VPL); Steel Balls (Set of 6) (STB-VPL); Goggles (Set of 2) (GGL-VPL); Hand Air Pump (PUMP-VPL); BT ...
- https://www.vernier.com/til/2592
- Go Direct Projectile Launcher Troubleshooting and FAQs ...
- Dec 13, 2018 ... Secondary Test: Check that the hand pump is securely attached to the valve on the launcher. ... Hand Air Pump (PUMP-VPL). Published: December 13, ...
- https://www.vernier.com/til/4196
- Go Direct Blood Pressure Troubleshooting and FAQs – Technical ...
- Dec 20, 2019 ... When the indicator light flashes green, set the bulb pump down on the table. ... air remaining in the cuff. Check the indicator light to ...
- https://www.vernier.com/til/4454
- Blood Pressure Sensor Troubleshooting and FAQs – Technical ...
- Oct 30, 2012 ... Troubleshooting · The readings displayed on the computer screen should be between 0 and 5 mm Hg before any air is pumped into the cuff.
- https://www.vernier.com/til/1426
- What are the specifications for the KidWind water pump?
- The KidWind video on the reports the minimum voltage as 1.7 volts and 50 mA. We have operated the pump at up to 5 volts....
- https://www.vernier.com/til/3172/
- Which generator should I use to pump water?
- Of the generators that come with the KidWind Advanced Wind Experiment Kit, the smaller generator (less than 1 inch diameter, labeled “High Torque Generator”) is...
- https://www.vernier.com/til/3130/
- How do I improve the results from a Motion Detector with an air track?
- Air tracks use small streams of air to hold up carts so that they move with very little friction. They used to be very popular...
- https://www.vernier.com/til/2053/
- Hand Dynamometer Troubleshooting and FAQs
- Specifications and User Guide Troubleshooting Additional Troubleshooting Specifications Calibration Calibrate? No. The sensor is custom calibrated before shipping. Related Products
- https://www.vernier.com/til/1431/
- Why does heart rate suddenly increase to abnormally high values when using the heart rate sensors with hand grips?
- Increases in heart rate can be caused by numerous artifacts, but the heart rate monitors that use the Snap-On Polar Module with hand grips, such as...
- https://www.vernier.com/til/4193/
- Go Direct Hand Dynamometer Troubleshooting and FAQs
- Specifications and User Guide Troubleshooting General: Press the power button on the sensor to turn it on. Connect your sensor as described in the Getting...
- https://www.vernier.com/til/4311/
- Can I reduce the noise in the signal from my Hand Dynamometer connected to NI-ELVIS?
- This information relates to connecting a to an NI-ELVIS interface. In some situations, the signal may be noisy. To fix this, simply place a resistor...
- https://www.vernier.com/til/11599/
- Why should I switch from an air track to a dynamics track?
- A lot of instructors who make the switch tell us that having something that does not make noise is a big improvement to the classroom...
- https://www.vernier.com/til/4292/
- Is it possible to order the receiver and transmitter portion of the Exercise or Hand-Grip Heart Rate Monitor separately?
- The Hand-Grip Heart Rate Monitor and the Exercise Heart Rate Monitor both use the Heart Rate receiver. The transmitter belt of the old Exercise Heart...
- https://www.vernier.com/til/815/
- How do I know if I have the new (2020) Hand Grips or older (pre 2020) Hand Grips for the Vernier Heart Rate Sensors
- Vernier sells four different types of Heart Rate Sensors. Two of these sensors, the Go Wireless Heart Rate and the Hand Grip Heart Rate Sensor...
- https://www.vernier.com/til/10504/
SAVE/SHARE YOUR CART