30 results for "Adjustable Two Foot Leveler"

• Are the new DTS carts and tracks compatible with the old ...

  In every case possible, the new style is compatible with the old style. Although the carts and tracks included in the Dynamics Cart and Track System (DTS) look different than the carts in the Vernier Dynamics System (VDS, discontinued), there are more similarities between the two systems than differences.The DTS is a refinement of the VDS, drawn from years of teacher feedback.

  https://www.vernier.com/til/3634

• How do I use two motion detectors or two motion encoders ...

  Level the track. Place a cart on the track at rest and observe its motion. Adjust the leveling feet accordingly. Place the second cart on the track. Place the two carts end to end near the middle of the track. Connect each Motion Detector to a Vernier interface. In software, zero each Motion Detector and reverse one of them.

  https://www.vernier.com/til/3384/

• CBLØ SYSTEM

  Important Texas Instruments makes no warranty, either expressed or implied, including but not limited to any implied warranties of merchantability

  https://www.vernier.com/til/wp-content/uploads/sites/2/2020/03/cbl-guide.pdf

• Centripetal Force Apparatus Troubleshooting and FAQs ...

  -Primary Test: Is the apparatus level? If not, follow these steps: 1. Secure the Counterbalance Carriage to the outer end of the Rotating Beam. 2. Place three of the masses in the carriage. 3. Use a flathead screwdriver to lower each foot on the CFA footer to its lowest height. 4. Give the Rotating Beam a very slow spin and watch its motion.

  https://www.vernier.com/til/2391

• My field is too bright when trying to view a slide with a ...

  1. Turn the sub-stage disk to a position that is part way between two settings to reduce the amount of light. 2. Take an 8 cm by 8 cm piece of aluminum foil and cut a small 1 mm by 1 mm hole in the center of it. Place the piece of foil over the lamp with the hole in the middle of the lamp.

  https://www.vernier.com/til/1687

• Pressure Sensor 400 Troubleshooting and FAQs - Technical ...

  -Two-foot section of nylon tubing -Two-foot section of plastic tubing. CALIBRATION The Pressure Sensor is calibrated to atmospheric pressure in Portland, Oregon before shipping. You may wish to recalibrate with the atmosphere of your region by doing a one-point calibration. 1. Connect the Pressure Sensor 400 to an interface and launch the ...

  https://www.vernier.com/til/3478

• Logger Pro Troubleshooting and FAQs

  General Troubleshooting Tips Try these first. Many issues can be solved in a few simple steps: [til 2094] System Requirements [til 1579] [til 1668] [til...

  http://www.vernier.com/til/2089/

• Graphical Analysis 4 won't open my .ambl file on Windows.

  Windows makes it very easy to launch two copies of Graphical Analysis at the same time. You’ll be able to tell this is happening on...

  http://www.vernier.com/til/4437/

• Networking for LabQuest 2 and LabQuest 3—FAQ and Troubleshooting

  This information pertains to LabQuest 2 and LabQuest 3. If you have an original LabQuest, see this article. INITIAL SETUP [til 2725] [til 2726] [til...

  http://www.vernier.com/til/2669/

• My school Wi-Fi requires a username and password (WPA2 Enterprise). Can LabQuest 2 or LabQuest 3 connect to this network?

  This information pertains to LabQuest 2 and LabQuest 3. If you have an original LabQuest, see this article. LabQuest 2 and LabQuest 3 support many...

  http://www.vernier.com/til/2665/

• How do I collect data using a Motion Encoder and a photogate simultaneously?

  There are a few reasons you might want to collect data with both a Motion Encoder and a photogate at the same time. One example...

  http://www.vernier.com/til/3862/

• How do I use Data Sharing when the source is on a different subnet?

  When computer networks are divided into multiple sub-networks (subnets), there are several ways of using the Connected Science System when devices are in a different...

  http://www.vernier.com/til/2752/

• How can I install Logger Pro on several computers? Is there an MSI file or a silent installer?

  With each new version of Logger Pro for Windows, we create a silent version of our installer. In Logger Pro 3.8.4 and later, this is...

  http://www.vernier.com/til/1681/

• How do I set up a LabQuest-generated network on LabQuest 2 or LabQuest 3?

  This information pertains to LabQuest 2 and LabQuest 3. If you have an original LabQuest, see this article. The soft access point function of the...

  http://www.vernier.com/til/2699/

• How do I calibrate a sensor in Logger Pro?

  In most cases it is not necessary to calibrate sensors; however, for optimum accuracy you may choose to perform a calibration. To perform any calibration,...

  http://www.vernier.com/til/2341/

• How do I deploy the Logger Pro silent installer with Group Policy?

  To install Logger Pro with the silent installer via Group Policy, you need to have your computers set up with a Windows Domain and a...

  http://www.vernier.com/til/3947/

• Why is my acceleration data so noisy in a Half-Atwood machine?

  One experimental set up that is popular for studying Newton’s Second Law is the Half-Atwood machine. In a Half-Atwood machine, a dynamics cart is tied...

  http://www.vernier.com/til/3400/

• Why are there icons/gears on the LabQuest Connections App screen?

  LabQuest 2 and LabQuest 3 have a rudimentary security feature meant to deter unwanted access to the connections settings. To regain full access to the...

  http://www.vernier.com/til/3011/

• My LabQuest 2 or LabQuest 3 won't connect to an Enterprise network and keeps prompting me for my passphrase, what can I do?

  If you are having trouble connecting to an Enterprise network and you keep getting prompted to reenter the passphrase, try the following… 1. Make sure...

  http://www.vernier.com/til/3760/

• My WPA2 Enterprise network requires a certificate, how do I install it on LabQuest 2 or LabQuest 3?

  To install a certificate you will need the certificate from your security server (refer to your IT department). It needs to be in Base64 encoding...

  http://www.vernier.com/til/2836/

• How do I connect an original LabQuest to my network?

  This information pertains to the original LabQuest. If you have LabQuest 2 or LabQuest 3, see this article. To connect an original LabQuest to a...

  http://www.vernier.com/til/2479/

• How do I connect a LabQuest 2 or LabQuest 3 to my network?

  This information pertains to LabQuest 2 and LabQuest 3. If you have an original LabQuest, see this article. Follow these steps to connect a LabQuest...

  http://www.vernier.com/til/3396/

• Why is there an exclamation point on the Wi-Fi networking icon on LabQuest 2?

  An exclamation point on the Wi-Fi icon indicates that the Wi-Fi connection has been made, but the Internet connection is being routed to another address....

  http://www.vernier.com/til/2717/

• Why can't I see Vernier Data Share when I enter the correct address in a browser?

  To connect to Vernier Data Share, make sure that Data Sharing is enabled and follow the below steps. 1. Make sure the LabQuest and mobile...

  http://www.vernier.com/til/2744/

• Common causes of problems with the silent installer

  We strongly recommend that you use the MSI file as-is. We have tested on a wide variety of systems. Although it is technically possible to...

  http://www.vernier.com/til/2364/

• Can I install Logger Pro 3 to run from a server or network location?

  Logger Pro 3 software for Windows will not be fully functional if it is installed on a network. Logger Pro is not like other software...

  http://www.vernier.com/til/469/

• How are magnets installed in Vernier Dynamics Carts and Adjustable End Stops?

  Magnets must be installed in a certain orientation to be compatible with other carts and with the . To install magnets so that carts will...

  http://www.vernier.com/til/2184/

• The nuts to connect the feet to my track don't fit into the slot underneath the track.

  The base units for the Vernier Dynamics System tracks attach by sliding a nut into the slot on the underside of the track. Some units...

  http://www.vernier.com/til/1679/

• Is TI-Graph Link network compatible?

  Yes and no. The program itself and the help file can be run from a network computer by as many users as you want, but...

  http://www.vernier.com/til/74/

• I have a pre-2.1.1 version of Logger Pro for Windows. When I run the program and try to use the Sensor Setup dialog, the program crashes. How do I fix this?

  This problem is unique to Windows NT 4.0/2000 and is a permissions issue. Download the latest version of Logger Pro at: http://www.vernier.com/tech/lpupdates.html then install that...

  http://www.vernier.com/til/754/

• Adjustable Two Foot Leveler