• Store
  • Downloads
  • Support
  • My Account
Technical Information Library
  • Grade Levels
    • Higher Education
    • High School
    • Middle School
    • Elementary School
  • District Solutions
  • Products
    • Shop All Products
    • Sensors
    • Software
    • Vernier Connections
    • Lab Books
    • Lab Equipment
    • Interfaces
    • Packages
    • How to Order
    • Catalog
  • Professional Development
    • Personalized Request
    • Webinars
  • Resources
    • The Vernier Blog
    • Experiments
    • White Papers
    • Videos
    • Grants & Awards
    • Product Manuals
    • Safety Data Sheets
Menu

How do I use a multimeter with a KidWind setup?

  • March 22, 2017
  • 0
The following PDF document shows how to use a multimeter to measure current or voltage in a KidWind setup. Two multimeters are needed to measure current and voltage at the same time. Multimeter Instructions A multimeter is an inexpensive way to...
Continue Reading →

Can I use a dishwasher to wash the Nalgene bottle that shipped with my O2 or CO2 Gas Sensor?

  • March 22, 2017
  • 0
It is recommended that you wash the Nalgene bottles by hand. This includes 250 mL Nalgene Bottle w/Lid (CO2-BTL) and the BioChamber 250 (BC-250). The bottles are made of Polyethylene terephthalate G copolymer (PETG). The maximum temperature the bo...
Continue Reading →

How do I set up LabQuest 2 to email data with a Gmail account?

  • March 22, 2017
  • 0
This information pertains to LabQuest 2. If you have a LabQuest 3, see this article. The original LabQuest does not support this feature. These instructions are for LabQuest 2s that have been updated to 2.7 or higher. If you have not updated your ...
Continue Reading →

How is the Go Direct SpectroVis Plus Spectrophotometer different than the SpectroVis Plus?

  • March 20, 2017
  • 0
In February of 2017, Go Direct® SpectroVis® Plus Spectrophotometer (GDX-SVISPL) replaced the SpectroVis Plus (SVIS-PL, discontinued). There are very few differences between the Go Direct SpectroVis Plus and the SpectroVis Plus (SVIS-PL) when...
Continue Reading →

What are the Calibration equations for the CO2 Gas Sensor

  • March 17, 2017
  • 0
The calibration equations for the CO2 Gas Sensors are listed below. They are divided into the old model (square body, pre-2007) and newer model (rounded body, post-2007). Sensor 'CO2 Gas' (-DIN and -BTA, pre-2007) Calibration 'CO2 ppm': ...
Continue Reading →

Arduino and SparkFun RedBoard Troubleshooting and FAQs

  • March 17, 2017
  • 0
Arduino is an open-source physical computing platform based on a simple microcontroller board as well as a development environment for writing software for the board. For introductory materials to using Vernier sensors with Arduino, see: https://www...
Continue Reading →

Logger Pro installer on Windows 10 installer asks for a restart

  • March 16, 2017
  • 0
Logger Pro installs and upgrades of version 3.13 and later on Windows 10 will frequently require a reboot to install certain files. The installer is detecting that files that it needs to copy onto the system are already loaded in memory. In order...
Continue Reading →

What cuvettes can I use in my UV-Vis or Fluorescence/UV-VIS Spectrophotometer?

  • March 15, 2017
  • 0
The UV-VIS Spectrophotometer comes with a set of two Starna Quartz cuvettes: Quartz Cuvettes (CUV-QUARTZ). The Fluorescence/UV-VIS Spectrophotometer comes with one Starna Fluorescence Quartz cuvette: Fluorescence/UV Quartz Cuvette (CUV-QUARTZ-FUV) Th...
Continue Reading →

What is the Z dimension or beam height of your Spectrometers?

  • March 15, 2017
  • 0
The Z dimension refers to the position of the light beam transmitting through the cuvette. It is an important specification when working with small-volume samples. Go Direct SpectroVis Plus: 8.5 mm UV-VIS Spectrophotometer: 8.5 mm Fluorescence/UV-VI...
Continue Reading →

I collected Absorbance data and then Fluorescence data (or emission data) with my spectrometer. I am now collecting Absorbance data again and my data does not look correct.

  • March 15, 2017
  • 0
Logger Pro 3.14 and LabQuest 2.7.2 or newer remember calibration settings between mode changes, so this should not be an issue if you are using the latest version of the software. Make sure you have updated. ...
Continue Reading →
  • «
  • 1
  • ...
  • 127
  • 128
  • 129
  • 130
  • 131
  • ...
  • 229
  • »
 
  • ©2025 All rights reserved
  • Privacy Policy | Cookie Policy | Legal Center | Doing Business with Us
By using this site, you agree to our use of cookies to improve your experience. Learn more in our Privacy Policy.
You can revoke your consent any time using the Revoke consent button.