Search
- Nitrate Ion-Selective Electrode Troubleshooting and FAQs
- Wait for the voltage reading to stabilize. Enter the concentration value of the Low Standard, then click or tap Keep. Important: Make sure the ISE is not ...
- https://www.vernier.com/til/1432
- General tips for using Ion Selective Electrodes (ISE).
- Jan 25, 2019 ... ... ISE is in the High and Low standards. These values are ... NO3 100 mg/L Standard NO3 ISE Solution (NO3-HST). Ca 10 mg/L Standard ...
- https://www.vernier.com/til/665
- Go Direct Nitrate Ion-Selective Electrode Troubleshooting and FAQs
- (The green LED will flash to indicate the sensor is connected.) Primary Test: Check the readings in the standards. The high should be around 100 mg/L. The low ...
- https://www.vernier.com/til/4348
- Calcium Ion-Selective Electrode Troubleshooting and FAQs
- Feb 6, 2015 ... Standard Ca ISE Solution (CA-LST)—Low Concentration; Standard Ca ISE Solution (CA-HST)—High Concentration; Electrode Storage Bottles (BTL-ES).
- https://www.vernier.com/til/1434
- Ammonium Ion-Selective Electrode Troubleshooting and FAQs
- Replacement Parts. Ammonium Replacement Module (NH4-MOD); Standard NH4 ISE Solution (NH4-LST)—Low Concentration; Standard NH ...
- https://www.vernier.com/til/1435
- Chloride Ion-Selective Electrode Troubleshooting and FAQs
- Nov 10, 2016 ... Place the electrode into the Low Standard. Wait for the voltage ... Standard Cl ISE Solution (CL-LST)—Low Concentration; Standard Cl ISE ...
- https://www.vernier.com/til/1433
- Potassium Ion-Selective Electrode Troubleshooting and FAQs
- May 5, 2015 ... Remove the ISE from the High Standard. Rinse the electrode well with ... Standard Potassium Solution (K-LST)—Low Concentration; Standard ...
- https://www.vernier.com/til/3115
- Can I use a Vernier Ion-Selective Electrode (ISE) with Arduino?
- Yes, it is possible to use a Vernier Ion-Selective Electrode (ISE) with an Arduino microcontroller. However, we do not recommend this combination unless you are...
- https://www.vernier.com/til/3635/
- Do you sell ISE Standards?
- Yes, we carry a high and low standard for each of our ISEs. These are used to calibrate the sensors. They come in 500 mL...
- https://www.vernier.com/til/759/
- Do any of your sensors require special storage?
- Yes, there are a few sensors that need to be stored properly in order to stay in good condition. Oxygen Gas Sensors should be stored...
- https://www.vernier.com/til/1060/
- How do I sterilize an Ion-Selective Electrode?
- Standard cleaning is best done with DI water. If sterilization is needed, use ethyl alcohol (typically >90%) or isopropyl alcohol (typically 60-70%) and swirl in...
- https://www.vernier.com/til/3389/
- ISEs connected to a Go Wireless Link are identified as a different sensor.
- When an Ion Selective Electrode (ISE) is connected to a Go Wireless Link, the attached sensor can be identified incorrectly. This happens when you have...
- https://www.vernier.com/til/3717/
- How can I have my ISE read mV output instead of mg/L?
- For Go Direct ISEs (order codes begin with GDX-), simply enable the sensor’s mV channel in the app. For most LabQuest ISEs (order codes end...
- https://www.vernier.com/til/1296/
- Can I use my third-party ISE with my Vernier equipment?
- Maybe. The answer to this depends on a couple of things. 1. Does your electrode have a BNC connector? If so, you can use it...
- https://www.vernier.com/til/2291/
SAVE/SHARE YOUR CART